Belimo to Honeywell and other retrofit damper motor kit ZD,ARD, M847D BH Kit1

Description

* Works as a replacement for Honeywell M847D series motors on popular ZD and ARD dampers, including M847D1004 and M847D1012 motors and other M847D series.
*Works as a replacement for Trol a Temp MSR,  RDMH,  and other dampers.
*Works on many 24vac dampers from Honeywell, Trol a Temp, Aprilaire, ZoneFirst, EWC, Robert Shaw, Research Products, Ztec, Buetler, Durozone and others with a 3/8 or smaller drive shaft (other kits available for other size drive shafts.
*works as a 24 volt replacement on any damper with a round drive shaft 3/8 or smaller in size
Our ebay store Damper Direct has many other retrofit kits and adapters to get almost any damper back in business-your satisfaction is guaranteed!
Belimo LMB24-3-T Motor and retrofit kit, which includes the Belimo LMB24-3-T motor, shaft adapter, anti rotation bracket and two self tapping sheet metal screws; anything else in the picture is for illustration purposes.
Tired of replacing spring return damper motors that get hot and burn out? The Belimo to Honeywell Retrofit Kit BHK-24 gets the the premier commercial grade Belimo LMB damper motor and adapter kit for about the same price as the Honeywell M847D1012 2 wire spring replacement motor. This kit will also work on virtually any other damper that has a shaft under 3/8 of an inch diameter.
*Retrofits the industry leading LMB24-3-T motor on to many residential dampers, including Honeywell, Suncourt, Robert Shaw, Invensys, April Air, Research Products Perfect Temp and any other damper with an external driveshaft 3/8 or less in diameter.
*5 year warranty
*Gets rid of spring return motors for better reliability and energy savings.
*Works with any brand of standard 24vac zone control system.
*Saves energy, extends motor life, far more powerful motor with 5 year warranty.
*requires three wires to motor and the mounting of the anti-rotation bracket with two self tapping screws, included.
*24vac 2 va damper motor
Spring return damper motors pull 8 to 10 va of continuous power since they must overcome the return spring. Besides wasting energy, the spring return motors get very hot, contributing to their often premature failure. The Belimo LMB24-3-T retrofit kit motor uses just 2va for  90 seconds, and never even gets warm to the touch! A five year warranty is best in the business, so stop replacing those overpriced spring return motors!
Your current damper has just two wires to the motor, will this 3 wire motor work?  Yes, but you will need a third wire from the zone control panel or thermostat to allow this 3 wire motor to work-very often, standard 4 wire thermostat wire will have been used so check the cable for extra wires. Most zone control panels support three wire motors, including all Honeywell panels, check your zone control board damper outputs for an unused terminal, if your damper outputs are labeled M1,M4, and M6, OR Power Open PO. Power Close PC  and Common C, you have all the outputs you need and are good to go.
Even if your zone panel has just two damper outputs, you can still use this kit since the Belimo LMB motor will accept an alternative wiring procedure that places full time 24vac power on terminals 1 and 2, and then uses the current zone board output for terminal 3.  Full illustrated instructions are included.
From Damper Direct, where zoning is our only business! We offer the service, support, and technical resources to help you design or service your Zone Control System.
We handle all major brands including Retrozone, Honeywell, EWC, Durozone, Enerzone Systems Corp., Robertshaw, Invensys and more. If you dont see it on ebay, please ask and we can do a special Ebay auction for the part you need.
Call 972 633 8104
for technical support or application questions.